You grind the slab, vacuum it twice, mix the primer, and roll it out. It looks flawless. Two hours later the surface is covered in tiny craters, each one ringed with a little crown of cured resin.
That is outgassing. It is one of the most common reasons a clean-looking epoxy job gets ripped up and redone. It is also one of the most preventable.
Most of the fix comes down to timing, temperature, and primer choice, not to buying a more expensive product. This guide covers why concrete releases gas, how to read the conditions on your slab, and what to do at each stage of primer application. It is written for installers, contractors, and the distributors who supply them.

What Outgassing Actually Is
Concrete is not a solid block. It is a porous material full of capillaries, voids, and microscopic air pockets. Even a dense, well-finished slab holds a surprising amount of trapped air and moisture vapor.
Outgassing is the release of that air through the surface. When you roll liquid epoxy over the slab, the resin seals the top of those pores. If the air inside expands, it has only one way out: up through the wet coating. It pushes through as a bubble. If the primer gels before the bubble breaks, the bubble freezes in place as a pinhole.
Outgassing is not the same thing as moisture vapor transmission. Vapor drive pushes water vapor up through the slab over weeks and months, and it causes blisters and delamination long after installation. Outgassing happens in the first few hours, and it is about expanding air. The two problems overlap, because a damp slab outgasses more, but they need different fixes. Mixing them up is how people end up solving the wrong problem.
Why Temperature Is the Real Trigger
Air expands when it warms and contracts when it cools. That is all outgassing is, and it explains almost everything about when it happens.
Say you start priming at 9 a.m. The sun is climbing, the slab is warming, and the air inside the concrete is expanding with it. Every pore under your fresh primer is pushing gas upward. The more the temperature rises during the open time of the coating, the more gas gets pushed out through it.
Now flip it. Start priming in the early afternoon, as the slab temperature peaks and begins to fall. The air in the pores contracts. Instead of pushing out, the slab draws in. It pulls primer down into the pores, which improves the mechanical bond and leaves no gas to form bubbles.
That is the single most useful rule in this article: prime while the slab is cooling, not while it is warming.
A few conditions make the problem worse:
- Direct sun on the slab, especially through windows or open dock doors
- A slab that has been heated overnight by radiant systems or space heaters
- Outdoor or semi-outdoor pours where the surface temperature swings 20°F or more across the day
- A warm, dry afternoon followed by a cool evening, which can feel safe but still swings the slab temperature hard
Check the slab, not the air. An infrared thermometer costs about the price of a lunch. Take readings at several spots across the floor, and keep taking them through the day. If the numbers are climbing, wait.
Moisture Makes It Worse
Dry concrete still outgasses, but wet concrete does it harder. Water in the pores turns to vapor as the slab warms, and vapor takes up far more space than liquid water. It adds to the air pressure pushing up through your primer.
Test before you coat. The standard methods are:
- ASTM F2170 (in-situ relative humidity probes): Most epoxy primers want readings at or below about 75–85% RH, depending on the product. Always check the technical data sheet for the exact limit.
- ASTM F1869 (calcium chloride test): Many manufacturers specify a maximum of around 3 lb per 1,000 sq ft per 24 hours.
- ASTM D4263 (plastic sheet test): A taped 18-inch square of polyethylene left for 16 hours. It is qualitative, but it catches a wet slab quickly and costs almost nothing.
Slab age matters too. New concrete needs time to cure and shed its mix water, and a common rule is 28 days before coating. Treat that as a minimum, not a guarantee. A thick slab poured in a humid month can still be wet well past day 28. Slabs on grade with no vapor barrier underneath may never get dry enough on their own.
If your readings are over the limit, a primer that tolerates moisture is not a workaround for pinholes. You need a moisture vapor barrier. Jincheng’s Moisture Vapor Barrier Primer is a two-component, 100% solids, zero-VOC system built for exactly this situation. It blocks the vapor drive that causes blistering later. It will not stop a slab from outgassing during application, so timing and application technique still matter on top of it.
Surface Preparation Sets Up the Result
Outgassing problems often begin before anyone opens a bucket.
Open the surface. Diamond grinding or shot blasting should leave a profile of roughly CSP 2–3 for thin-film primers and coatings. A smooth, closed surface traps air under the coating, while an open profile lets it escape and lets primer penetrate. Power-troweled slabs and ones with curing compounds or sealers need particular attention here, since their surface layer can be dense and almost glassy.
Remove laitance and contamination. The weak cement paste on top of a slab crumbles under load and acts like a lid on the pores below. Grind it off. Oils, silicone-based curing agents, and old adhesive residues cause their own defects, such as fish eyes and poor adhesion, and they can also mask moisture problems.
Vacuum, don’t just sweep. Dust fills the same pores you want the primer to enter. Use an industrial vacuum with a HEPA filter, then a second pass. Compressed air blown across the slab only moves dust around and drops it back down.
Fix the defects first. Open cracks, bug holes, and spalled edges are outgassing highways. Patch them with epoxy mortar or a compatible repair product and let it cure before priming. A hole you can see is a pinhole you will get.
Choosing the Right Primer
Not all primers handle porous concrete equally, and the differences show up fast.
Viscosity matters most. A low-viscosity primer flows into the pores and wets them out. A thick primer sits on top, bridges across the openings, and traps whatever gas is underneath. For problem slabs, thin and penetrating beats thick and buildy.
Solids content has a trade-off. A 100% solids primer leaves no solvent to flash off and has no shrinkage as it cures, which helps it seal. Solvent-borne primers penetrate well but release solvent vapor that can itself form bubbles in a thick film. Pick one system and apply it at the manufacturer’s spread rate. Do not thin it to stretch coverage.
Pot life and gel time set your window. A slow-curing primer gives bubbles time to rise and pop before the surface sets. A fast one locks them in. Conversely, a primer that stays tacky for hours in a warm room gives outgassing more time to do damage. Read the technical data sheet, find the working time at your actual slab temperature, and plan around it.
Application Technique That Reduces Pinholes
Once conditions are right and the primer is right, how you put it down still counts.
Apply in the cooling window. Start in the mid-to-late afternoon, once slab temperature has peaked and begun to drop. Take a reading before you start and another about an hour in. If the trend flips upward, stop and reassess.
Work it in. Pour the mixed primer in a ribbon, spread it with a squeegee, then back-roll with a medium-nap roller. The squeegee pushes material into the pores. The roller evens it out and breaks surface bubbles. Brushing along edges and into profile valleys helps in the same way.
Consider two thin coats. One thin pass seals the pores and lets them outgas under controlled conditions. A second pass, applied within the recoat window, covers any pinholes the first one left. This often beats a single heavy coat, which is far more likely to trap gas.
Use a scratch coat on rough slabs. Where the surface is badly pitted or very absorbent, an epoxy scratch coat or grout coat, thickened with fine silica sand, fills the voids before the main primer goes on. It takes more labor but is cheaper than a failed floor.
Back-roll as it cures. Walk the floor in spiked shoes or go back over it with a short-nap roller while the primer is still workable. Any bubbles that rise can be popped before they set. Do not use a heat gun or torch on a primer film to chase bubbles. Heating the film heats the slab beneath it, which drives more gas up.
Control the room. Close off direct sun. Keep fans pointed away from the wet surface, because moving air skins the primer and traps bubbles beneath the skin. Do not run heaters during application. If the building has radiant heat, shut it off well ahead of time and let the slab stabilize.
Test Patch First
If you are unsure about a slab, run a test. Mix a small amount of primer and apply it to a two-foot square in the same conditions and at the same time of day you plan to coat. Come back in an hour and look at it with a flashlight held at a low angle. Pinholes and bubbles show up as tiny shadows. The test costs a cup of primer and tells you whether the real application will work.
You can do the same with the plastic sheet or a dab of clear sealer on a bare spot. The aim is to watch how that particular slab behaves, not to trust a general rule.
What to Do If Pinholes Appear
It still happens, even to careful crews. The fix depends on how far the primer has cured.
While still wet or tacky: Back-roll again and, if there is time, apply a thin second pass. Often the pinholes close on their own.
After full cure: Sand or grind the surface lightly to knock down the crowns, vacuum thoroughly, and apply another thin coat of primer or a filler coat. For clusters of pinholes, a squeegeed grout coat works well. Individual pinholes can be spot-filled with a thickened epoxy.
Do not coat over open pinholes. Whatever goes on top, whether it is a base coat, broadcast flake, or a metallic system, will telegraph every defect and may also trap air. Pinholes in a primer become craters in a finished floor. Fix them at the primer stage, where they are cheap.
Putting It Together
A reliable workflow for a problem slab looks like this:
- Test moisture with RH probes or calcium chloride, and install a vapor barrier if the numbers are over the limit.
- Grind or shot blast to the right profile, repair defects, and vacuum thoroughly.
- Check the slab temperature on the morning of the job and plan to start when it is falling.
- Choose a low-viscosity, penetrating primer and apply it at the specified rate.
- Squeegee, back-roll, and watch the slab temperature through the work.
- Inspect at a low angle before the recoat window closes, and fix defects before moving on.
None of this is exotic. It is just a matter of treating concrete as a living, breathing substrate and not as a flat surface to paint on.
A Note for Distributors and Private-Label Buyers
If you supply installers, outgassing complaints will come to you, even when the cause was timing. Reduce them by giving crews clear guidance on application windows and slab temperature, and by choosing primers whose viscosity and pot life suit your market’s climate. A hot-climate formulation and a cold-climate formulation are not the same product.
Jincheng Resin manufactures epoxy primers, moisture vapor barriers, and complete floor coating systems, and supports OEM and private-label programs with adjustable viscosity, working time, and packaging. If your installers are fighting pinholes, we can help you match the formula to the conditions they actually work in.